O.E.M cylinders and pistons

Cylinder and piston kit Trészer Brushcutters HU 125, 128

Cylinder and piston kit Trészer Brushcutters HU 125, 128
39.48 EUR

Cylinder included HUSQVARNA 125, 128, 35mm. Catalog number - 06-61-049 The cylinder diameter is 35m...

Cylinder included HUSQVARNA 125, 128, 35mm. Catalog number - 06-61-049

The cylinder diameter is 35mm

In the delivery of the piston group includes: cylinder, piston, piston rings, pin and fast ring rings

The cylinder seat is executed to install on the gasket.

Coverage of cylinder walls - Industrial chrome hardness 68 HRC

The thickness of the walls of the cylinder is chromium - 0.21 mm

Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile

Rules for replacing a piston group chainsaw and motorcycles.

  1. Check that the cylinder you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important to remove an old fuel tank fuel.
  3. Set a new fuel filter. If you use an old fuel filter, remove all fossil fuels from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a little lubricant to bearings. Try to use the highest quality lubricant.
  6. Wipe the new cylinder with a solvent with a solvent and purge air from the compressor.
  7. Install the rings on the piston of mark up.
  8. Lubricate the piston's pin and install the piston so that the arrow on it indicates the exhaust direction.
  9. Very carefully install the locking rings, do not bend but do not twist them.
  10. grease the cylinder and piston rings.
  11. Gently set the cylinder. Use adaptations to compress a piston rings.
  12. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. Some models uses a sealant.
  13. tighten the screws with the efforts of the specified manufacturer.
  14. Gently check the engine. Make sure it rotates freely and without interference.
  15. For first refueling, make a fuel mixture in a ratio of 25 - 1 and launch a chainsaw or motorcycle
  16. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions can lead to a regular failure of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters Om Sparta 25, 250, EFCO

Cylinder and piston kit Trészer Brushcutters Om Sparta 25, 250, EFCO
121.19 EUR

Piston group OLEO-MAC SPARTA 25, 250. Catalog number - 06-61-166 Piston cylinder for OLEO-MAC motor...

Piston group OLEO-MAC SPARTA 25, 250. Catalog number - 06-61-166

Piston cylinder for OLEO-MAC motorcycle, EFCO

The cylinder with a piston is used in Motorcase Sparta 25, Sparta 25TR, Sparta 250, Stark 25, Stark 25tr,.

Includes piston delivery you will find:
Cylinder with covers of chromium walls - 1 pc - Piston with m asloinsible nasech - 1pcs
Piston ring - 1pcs
Ring Stop Piston - 1pcs
Piston pin - 1pc

Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile

Rules for replacing a piston group chainsaw and motorcycles.

  1. Check that the cylinder you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important to remove an old fuel tank fuel.
  3. Set a new fuel filter. If you use an old fuel filter, remove all fossil fuels from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a little lubricant to bearings. Try to use the highest quality lubricant.
  6. Wipe the new cylinder with a solvent with a solvent and purge air from the compressor.
  7. Install the rings on the piston of mark up.
  8. Lubricate the piston's pin and install the piston so that the arrow on it indicates the exhaust direction.
  9. Very carefully install the locking rings, do not bend but do not twist them.
  10. grease the cylinder and piston rings.
  11. Gently set the cylinder. Use adaptations to compress a piston rings.
  12. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. Some models uses a sealant.
  13. tighten the screws with the efforts of the specified manufacturer.
  14. Gently check the engine. Make sure it rotates freely and without interference.
  15. For first refueling, make a fuel mixture in a ratio of 25 - 1 and launch a chainsaw or motorcycle
  16. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions can lead to a regular failure of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters Om Sparta 37, 38, 42, 44, 40mm

Cylinder and piston kit Trészer Brushcutters Om Sparta 37, 38, 42, 44, 40mm
46.63 EUR

Applies to OLEO-MAC Sparta 37, Sparta 38, Sparta 42, Sparta 44, EFCO Stark 37, Sparta 44, EFCO Stark...

Applies to OLEO-MAC Sparta 37, Sparta 38, Sparta 42, Sparta 44, EFCO Stark 37, Sparta 44, EFCO Stark 37, Stark 38, Stark 42, Stark 44.

Piston cylinder:

Piston diameter - 40mm.

The thickness of the piston ring is 1.5 mm.

Diameter of the pin - 10mm.

The delivery kit includes:

Cylinder - 1pc

Piston - 1pc

Piston rings - 2pcs

pin - 1pc

pin-locking rings - 2pcs

Coverage Cylinder - Chrome. Class of manufacture - A. Technology - molding under pressure.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters Om Sparta 40, 740T, EFCO 8400, 40mm

Cylinder and piston kit Trészer Brushcutters Om Sparta 40, 740T, EFCO 8400, 40mm
51.67 EUR

Applies to OLEO-MAC SPARTA 40, 740 T, EFCO 8400 brushcutter models. Piston and cylinder complete: ...

Applies to OLEO-MAC SPARTA 40, 740 T, EFCO 8400 brushcutter models.

Piston and cylinder complete:

Piston diameter - 40mm.

The thickness of the piston ring is 1.5 mm.

Diameter of the pin - 9mm.

The delivery kit includes:

Cylinder - 1pc

Piston - 1pc

Piston rings - 2pcs

pin - 1pc

pin-locking rings - 2pcs

Coverage Cylinder - Chrome. Class of manufacture - A. Technology - molding under pressure.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters ST FS250, FS350, 40mm

Cylinder and piston kit Trészer Brushcutters ST FS250, FS350, 40mm
53.1 EUR

Used in brushcutters Stihl FS250, FS350. Piston and cylinder kit: Cylinder diameter - 40mm. The t...

Used in brushcutters Stihl FS250, FS350.

Piston and cylinder kit:

Cylinder diameter - 40mm.

The thickness of the piston ring is 1.5 mm.

The delivery kit includes:

Cylinder - 1pc

Piston - 1pc

Piston rings - 2pcs

pin - 1pc

pin-locking rings - 2pcs

Coverage Cylinder - Chrome. Class of manufacture - A. Technology - molding under pressure.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters ST FS38, FS45, FS55, 34mm

Cylinder and piston kit Trészer Brushcutters ST FS38, FS45, FS55, 34mm
59.57 EUR

Piston group to Stihl Motk. Applies to STIHL FS38, FS45, FS55 models. Complete piston: cylinder, pi...

Piston group to Stihl Motk. Applies to STIHL FS38, FS45, FS55 models.

Complete piston: cylinder, piston, two piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

Diameter of the cylinder internal - 34mm.

The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor.

Pay attention! Due to the fact that the listed models have the same landing under the cylinder, we can use this piston on each of them.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Please note! For installation of a piston group on a release motorcycle before 2014, regular screws should be used. In motorcycles of the Chinese release assembly after 2014, with a piston for one ring, use screws with a nut, a washer and gravel. M5x65mm screw size.

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters ST FS400, FS450, 42mm

Cylinder and piston kit Trészer Brushcutters ST FS400, FS450, 42mm
71.48 EUR

Piston group to Stihl Motk. Applies to STIHL FS400, FS450 models Complete piston: cylinder, piston,...

Piston group to Stihl Motk. Applies to STIHL FS400, FS450

models

Complete piston: cylinder, piston, two piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

The diameter of the cylinder is internal - 42mm.

diameter of the piston pin 10 mm.

Length of the piston pin 28mm.

The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor.

Pay attention! Due to the fact that the listed models have the same landing under the cylinder, we can use this piston on each of them.

Original code STIHL # 41280201211

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters TL33, 36mm

Cylinder and piston kit Trészer Brushcutters TL33, 36mm
25.03 EUR

Cylinder Complete Motorcoats 330, 36mm. Catalog number - 06-61-079 Ports group of this type is used...

Cylinder Complete Motorcoats 330, 36mm. Catalog number - 06-61-079

Ports group of this type is used in models of Chinese motorcycle production with index 330. The piston diameter is 36 mm

Specifications of the piston group:

Piston diameter - 36 mm

Piston height - 36 mm

Piston skirt - 24 mm

The hot belt is 4.5 mm

Sealing belt - 5.5 mm

Height of grooves under the compression ring - 1.5 mm

Diameter for a piston pin - 9 mm

Size of piston rings

thickness of the compression ring - 1.5 mm

Ring Diameter - 36 mm

piston pin size

Length - 29 mm

Diameter external - 9 mm

Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile

Rules for replacing a piston group chainsaw and motorcycles.

  1. Check that the cylinder you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important to remove an old fuel tank fuel.
  3. Set a new fuel filter. If you use an old fuel filter, remove all fossil fuels from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a little lubricant to bearings. Try to use the highest quality lubricant.
  6. Wipe the new cylinder with a solvent with a solvent and purge air from the compressor.
  7. Install the rings on the piston of mark up.
  8. Lubricate the piston's pin and install the piston so that the arrow on it indicates the exhaust direction.
  9. Very carefully install the locking rings, do not bend but do not twist them.
  10. grease the cylinder and piston rings.
  11. Gently set the cylinder. Use adaptations to compress a piston rings.
  12. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. Some models uses a sealant.
  13. tighten the screws with the efforts of the specified manufacturer.
  14. Gently check the engine. Make sure it rotates freely and without interference.
  15. For first refueling, make a fuel mixture in a ratio of 25 - 1 and launch a chainsaw or motorcycle
  16. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions can lead to a regular failure of chainsaw or motorcycle.

Cylinder and piston kit Trészer Brushcutters TL43, 40mm

Cylinder and piston kit Trészer Brushcutters TL43, 40mm
27.03 EUR

Piston group to motorcycle. Applies in Chinese motorcycles, Russian and inexpensive European brands....

Piston group to motorcycle. Applies in Chinese motorcycles, Russian and inexpensive European brands. To motorcycle model 430 with a piston 40mmIt can also be installed on motorcycles with a piston 44mm due to a universal cylinder landing.

Complete piston: cylinder, piston, two piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

Diameter of the cylinder inner - 40mm.

Diameter of the piston pin - 10 mm.

The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Chainsaw 3800, 39mm

Cylinder and piston kit Trészer Chainsaw 3800, 39mm
26.26 EUR

Applies to repair Chinese, Russian, Belarusian and cheap European chainsaws of all brands, models 38...

Applies to repair Chinese, Russian, Belarusian and cheap European chainsaws of all brands, models 3800. Diameter of piston 39mm. The thickness of the piston ring is 1.5mm.

In the package of s includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 1pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Chainsaw Hu 136, 137, 142, 40mm

Cylinder and piston kit Trészer Chainsaw Hu 136, 137, 142, 40mm
36.83 EUR

. The piston group is used for repairing HUSQVARNA chainsaw, models 136, 137, 142. Piston diameter ...

. The piston group is used for repairing HUSQVARNA chainsaw, models 136, 137, 142.

Piston diameter 40mm.

The thickness of the piston ring is 1.5mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston ring - 1pc.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Chainsaw Hu 235, 236, 240, 39mm

Cylinder and piston kit Trészer Chainsaw Hu 235, 236, 240, 39mm
35.74 EUR

Cylinder with a HUSQVARNA 235, 236, 240, 39mm. Catalog number - 06-61-046 This piston group is use...

Cylinder with a HUSQVARNA 235, 236, 240, 39mm. Catalog number - 06-61-046

This piston group is used in chainsaws HUSQVARNA 235, 236, 240, 340 MCCULLOCH, JONSERED CS2234, CS2238

In the delivery of the piston group includes: cylinder, piston, piston rings, pin and locking rings.

Diameter of the cylinder internal - 39mm

Coverage of cylinder walls - Industrial chrome hardness 68 HRC

The thickness of the walls of the cylinder is chromium - 0.21 mm

All the listed models of chainsaw Husqvarna, McCulloch and Jonsered are made on a single platform and differ only in the inner diameter of the cylinder and, accordingly, with power.

The cylinders of all these models have the same mounting sizes. Due to this, 61-046 the cylinder approaches all these models of chainsaw HUSQVARNA, MCCULLOCH and JONSERED.

The cylinder has a chrome coating and a prolonged life resource.

Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile

Rules for replacing a piston group chainsaw and motorcycles.

  1. Check that the cylinder you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important to remove an old fuel tank fuel.
  3. Set a new fuel filter. If you use an old fuel filter, remove all fossil fuels from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a little lubricant to bearings. Try to use the highest quality lubricant.
  6. Wipe the new cylinder with a solvent with a solvent and purge air from the compressor.
  7. Install the rings on the piston of mark up.
  8. Lubricate the piston's pin and install the piston so that the arrow on it indicates the exhaust direction.
  9. Very carefully install the locking rings, do not bend but do not twist them.
  10. grease the cylinder and piston rings.
  11. Gently set the cylinder. Use adaptations to compress a piston rings.
  12. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. Some models uses a sealant.
  13. tighten the screws with the efforts of the specified manufacturer.
  14. Gently check the engine. Make sure it rotates freely and without interference.
  15. For first refueling, make a fuel mixture in a ratio of 25 - 1 and launch a chainsaw or motorcycle
  16. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions can lead to a regular failure of chainsaw or motorcycle.

Cylinder and piston kit Trészer Chainsaw Hu 340, 345, 42mm

Cylinder and piston kit Trészer Chainsaw Hu 340, 345, 42mm
53.1 EUR

. Piston Group to Chainsaw Husqvarna and Jonsered. Used in models 340, 345, CS2141, CS2145. Complet...

. Piston Group to Chainsaw Husqvarna and Jonsered. Used in models 340, 345, CS2141, CS2145.

Complete piston: cylinder, piston, piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

The diameter of the cylinder is internal - 42mm.

The coating of the chromium cylinder walls allows you to obtain a resource of work to a fracture of about 900 motor.

Pay attention! Due to the listed models have the same landing under the cylinder, we can use this piston on each of them. For Models Husqvarna 345 and Jonsered CS2145 This piston will feature the original A for the HUSQVARNA 340 and JONSERED CS2141 model, we will receive a large power due to an increase in the cylinder diameter with 40mm to 42 mm.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Chainsaw Hu 350, 351, 353, JO CS2150, CS2152, 44mm

Cylinder and piston kit Trészer Chainsaw Hu 350, 351, 353, JO CS2150, CS2152, 44mm
39.82 EUR

It is used for repairing chainsaws of the brand HUSQVARNA, models: 346, 350, 351, 353, and dust JONS...

It is used for repairing chainsaws of the brand HUSQVARNA, models: 346, 350, 351, 353, and dust JONSERED Models: 2149, CS2150, CS2152, CS2153. Diameter of piston 44mm. The thickness of the piston ring is 1.5mm.

The landing place of the piston group in these models of chainsaw is the same. This technical solution allows you to use one CPG for all these dust.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 1pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium to improve the removal of heat and increase the resource. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder and piston kit Trészer Chainsaw Hu 365, 372, 48mm

Cylinder and piston kit Trészer Chainsaw Hu 365, 372, 48mm
55.82 EUR

. Piston Group to Chainsaw Husqvarna and JonseredIt is used in models 365, 371xp, 372xp, CS2165, CS2...

. Piston Group to Chainsaw Husqvarna and JonseredIt is used in models 365, 371xp, 372xp, CS2165, CS2171, CS2172.

Complete piston: cylinder, piston, piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

Diameter of the cylinder internal - 48mm.

The coating of the chromium cylinder walls allows you to obtain a resource of work to a fracture of about 900 motor.

Pay attention! Due to the listed models have the same landing under the cylinder, we can use this piston on each of them.

original code husqvarna # 5039390-07

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

  1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
  2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
  3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
  4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
  5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
  6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
  7. Very carefully install the locking rings, do not bend and do not twist them.
  8. Lubricate the cylinder and piston rings.
  9. Carefully set the cylinder. Use a compression of rings.
  10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
  11. tighten the screws with the efforts specified by the manufacturer.
  12. Gently check the engine. Make sure it rotates freely and without interference.
  13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
  14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Showing 1 to 15 of 78 (6 Pages)

Our company produce gravity cast cylinders for almost half of the century. We are proud to be at the leading position in industry. Cylinders for garden gasoline powered motor units it`s a traditional field for our manufacturing facilities.

We start cylinders production in 1968. At the beginning it`s was very short range of products. We start with few models for Husqvarna and BMW motorcycles and couple of cylinders types for STIHL and DOLMAR gasoline powered chainsaws .

Now we have wide range of products which is cover almost full worldwide popular models from most well known manufacturers. Top quality of our cylinders meet international industry standards.

TRESZER pistons and piston rings production have a long history. We start pistons manufacturing  at 1956. Since this time we increase the number of items in our range of pistons and rings. At the present time we cover  almost all most  popular models of brushcutters and chainsaws.

We are proud to produce best quality products for our valued customers worldwide.