O.E.M cylinders and pistons
Piston Trészer Chainsaws ST MS361, 47mm
Piston is used for repairing chainsaw stihl brands, MS361 models. Suitable for the dust of this mode...
Piston is used for repairing chainsaw stihl brands, MS361 models. Suitable for the dust of this model, all years of release. Diameter of piston 47mm.
The piston delivery kit includes:
Piston with oil-containing crop - 1pc.
Ring of piston thickness 1.2 mm - 2 pcs.
pin - 1pc.
pin Rings - 2pcs.
Formal cardboard packaging - 1pc.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Cylinder and piston kit Trészer Chainsaw Hu 357, 359, 47mm
It is used for repairing chainsaws of Husqvarna brand, models 357, 359. Diameter of piston 47mm. The...
It is used for repairing chainsaws of Husqvarna brand, models 357, 359. Diameter of piston 47mm. The thickness of the piston ring is 1.5mm.
The cylinder supplies with a piston to chainsaw includes:
Cylinder - 1pc.
Piston - 1pc.
Piston rings - 1pcs.
pin - 1pc.
Piston Rings - 2pcs
The cylinder mirror is covered with chromium to improve the removal of heat and increase the resource. The piston group comes in cardboard packaging.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Instructions for installing a new cylinder chainsaw and motorcycle
- Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
- Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
- Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
- Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
- Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
- Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
- Very carefully install the locking rings, do not bend and do not twist them.
- Lubricate the cylinder and piston rings.
- Carefully set the cylinder. Use a compression of rings.
- Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
- tighten the screws with the efforts specified by the manufacturer.
- Gently check the engine. Make sure it rotates freely and without interference.
- For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
- Adjust the carburetor and protest the tool in operation.
Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.
Piston Trészer Brushcutters OM SPARTA 25, EF Stark 25, 34mm
Piston for brushcutters. Used to repair Moto-Mac Sparta 25, SPARTA 250T, EFCO STARK 25. Diameter of ...
Piston for brushcutters. Used to repair Moto-Mac Sparta 25, SPARTA 250T, EFCO STARK 25. Diameter of piston 34mm.
The piston delivery kit includes:
Piston with oil-containing crop - 1pc.
Ring piston thickness of 1.5 mm - 1pc.
pin - 1pc.
pin Rings - 2pcs.
Formal cardboard packaging - 1pc.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Piston Trészer Brushcutters ST FS38, FS45, FS55, 34mm
Piston complete with rings for brushcutters. Applies in brushcutters stihl rings, pin. Piston diame...
Piston complete with rings for brushcutters. Applies in brushcutters stihl rings, pin.
Piston diameter - 34mm.
Thickness of piston rings - 1,5mm.
Radial nasech, executed on the walls of the piston, allows you to hold an oil film to improve cooling.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Piston Trészer Brushcutters ST FS450, 42mm
Piston STIHL FS450, 42mm. Catalog number - 08-62-134 Includes delivery of this piston you will find...
Piston STIHL FS450, 42mm. Catalog number - 08-62-134
Includes delivery of this piston you will find: piston, two piston rings, pin, two stop piston rings
Piston diameter - 42 mm
Diameter of the piston pin 10 mm
Length of the piston pin 28 mm. The piston has a nutshell to provide high-quality lubricant.
Original code STIHL # 41280302005
Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile
Piston Trészer Chainsaw 3800, 39mm
Piston chainsaws 3800, 39mm. Catalog number - 08-62-148 Piston in the kit used for repairing chains...
Piston chainsaws 3800, 39mm. Catalog number - 08-62-148
Piston in the kit used for repairing chainsaw Chinese brands model 3800
The piston diameter is 39 mm. Includes delivery you will find: piston, piston rings with a diameter of 39mm, locking rings and pin
Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile
Piston Trészer Chainsaw 5800, D 42.5 mm
Piston chainsaw models 5800, 45.2 mm. Catalog number - 08-62-127 Such a piston is used in Chinese c...
Piston chainsaw models 5800, 45.2 mm. Catalog number - 08-62-127
Such a piston is used in Chinese chainsaws 5800
Piston diameter 45.2 mm
Diameter of the pin - 11mm
Includes you will find: piston, two piston rings, two locking rings, pin
Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile
Piston Trészer Chainsaw Hu 236, 240, 39mm
Piston chainsaws HUSQVARNA 236, 240, 39mm. Catalog number - 08-62-123 Applies in chainsaws HUSQVARN...
Piston chainsaws HUSQVARNA 236, 240, 39mm. Catalog number - 08-62-123
Applies in chainsaws HUSQVARNA 236, 240, JONSERED CS2234, CS2238
The diameter of this piston is 39mm
Includes piston you will find:
Piston - 1pc
Piston ring - 1pc
Piston pin - 1pc
Ring the fasten pin - 2pcs
Piston can be installed on all of these models of chainsaws all years of release.
Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile
Piston Trészer Chainsaw Hu 340, 40mm
Piston chainsaws Husqvarna 340, 40mm. The catalog number is 08-62-015 Piston of this type is used f...
Piston chainsaws Husqvarna 340, 40mm. The catalog number is 08-62-015
Piston of this type is used for repairing chainsaws HUSQVARNA 340 models, JONSERED CS2141. Includes piston delivery you will find: piston in diameter 40 mm, piston ring thickness 1.5 mm - 1pc, pin, locking rings 2 pcs
Piston diameter - 40 mm
Height of grooves under the compression ring - 1.5 mm
Diameter for a piston pin - 10 mm
Pin lenghts 30mm
Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile
Piston Trészer Chainsaw Hu 365, JS C2165, 48mm
Piston is used for repairing chainsaws of the brand HUSQVARNA, models 365, JONSERED CS2165. Suitable...
Piston is used for repairing chainsaws of the brand HUSQVARNA, models 365, JONSERED CS2165. Suitable for the dust of this model, all years of release. Diameter of piston 48mm.
The piston delivery kit includes:
Piston with oil-containing crop - 1pc.
Ring piston thickness of 1.5 mm - 1pc.
pin - 1pc.
pin Rings - 2pcs.
Formal cardboard packaging - 1pc.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Piston Trészer Chainsaw OM 936, 937, 38mm
Piston is used for repairing chainsaw OLEO-MAC 937, 936, EFCO 137. Diameter of piston 38mm. The pis...
Piston is used for repairing chainsaw OLEO-MAC 937, 936, EFCO 137. Diameter of piston 38mm.
The piston delivery kit includes:
Piston with oil-containing crop - 1pc.
Ring piston thickness of 1.5 mm - 1pc.
pin - 1pc.
pin Rings - 2pcs.
Formal cardboard packaging - 1pc.
Original OLEO-MAC code # 50110066A
This piston is suitable for all chainsaw OLEO-MAC models 937 as well as EFCO 137 all years of release.
Up to chainsaw OLEO-MAC 936 Use the following manual:
If your chainsaw is released before 18.09.2006 and has a factory number to 0356383719 then you need an original piston with code 50050131A.
If your chainsaw is released after 18.09.2006 and has a factory number above 0356383720 then use this piston.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Piston Trészer Chainsaw PA, JS, 41mm
Piston chainsaw partner, Jonsered, 41mm. The catalog number is 08-62-056 Piston in such a complete ...
Piston chainsaw partner, Jonsered, 41mm. The catalog number is 08-62-056
Piston in such a complete set in chainsaws 352 for partners, 371, JONSERED CS2138, POULAN 2150, 2250
Piston diameter 41 mm.
Includes piston you will find: piston, piston rings, locking rings, piston pin
Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile
Piston Trészer Chainsaw St MS250, 42,5mm
Piston chainsaws STIHL MS250, 42,5 mm. Catalog number - 08-62-003 In the delivery set of this pisto...
Piston chainsaws STIHL MS250, 42,5 mm. Catalog number - 08-62-003
In the delivery set of this piston you will find: piston with a diameter of 42.5 mm, piston rings of a thickness of 1.2 mm - 2 pcs, pin, fixing rings of pins 2 pieces
Diameter of the piston pin 10 mm
Length of the piston pin 28 mm.
Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile
Piston Trészer Chainsaws ST MS180, 38mm
Piston is used in repairing chainsaw stihl brands, MS180 models. Piston diameter 38mm. Diameter of...
Piston is used in repairing chainsaw stihl brands, MS180 models.
Piston diameter 38mm.
Diameter of 7mm.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Piston Trészer Chainsaws ST MS210, MS230
Piston Trészer Chainsaws ST MS210, MS230 Article for ordering manufacturer Trészer - 08-62-116 Incl...
Piston Trészer Chainsaws ST MS210, MS230 Article for ordering manufacturer Trészer - 08-62-116
Includes piston delivery: rings, piston, pin locks.
Manufacturer Trészer - Germany.
Hochwertige Bauteile
Our company produce gravity cast cylinders for almost half of the century. We are proud to be at the leading position in industry. Cylinders for garden gasoline powered motor units it`s a traditional field for our manufacturing facilities.
We start cylinders production in 1968. At the beginning it`s was very short range of products. We start with few models for Husqvarna and BMW motorcycles and couple of cylinders types for STIHL and DOLMAR gasoline powered chainsaws .
Now we have wide range of products which is cover almost full worldwide popular models from most well known manufacturers. Top quality of our cylinders meet international industry standards.
TRESZER pistons and piston rings production have a long history. We start pistons manufacturing at 1956. Since this time we increase the number of items in our range of pistons and rings. At the present time we cover almost all most popular models of brushcutters and chainsaws.
We are proud to produce best quality products for our valued customers worldwide.