O.E.M cylinders and pistons

Applicable in models: Chinese chainsaw models 5200, Russian, Belarusian and inexpensive European br...

Applicable in models:

Chinese chainsaw models 5200, Russian, Belarusian and inexpensive European brands.

The diameter of the piston ring is 45mm.

Ring thickness - 1.2 mm.

Price specified for a set of two rings.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Quality: Premium Substitution.

Applicable in models: HUSQVARNA 365 and JONSERED CS2165 Diameter of the piston ring - 48mm. Ring ...

Applicable in models:

HUSQVARNA 365 and JONSERED CS2165

Diameter of the piston ring - 48mm.

Ring thickness - 1.5 mm.

Ring thickness - 1.2 mm.

The price is indicated on one ring.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Applies to OLEO-MAC 753 T, EFCO 8550 motorcycle models. Piston and cylinder kit: Piston diameter -...

Applies to OLEO-MAC 753 T, EFCO 8550 motorcycle models.

Piston and cylinder kit:

Piston diameter - 45mm.

The thickness of the piston ring is 1.5 mm.

The delivery kit includes:

Cylinder - 1pc

Piston - 1pc

Piston rings - 2pcs

pin - 1pc

pin-locking rings - 2pcs

Coverage Cylinder - Chrome. Class of manufacture - A. Technology - molding under pressure.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Postera chainsaw. The piston group is used for the repair of Chinese, Russian, Belarusian and cheap ...

Postera chainsaw. The piston group is used for the repair of Chinese, Russian, Belarusian and cheap European chainsaws of all brands, models 4500.

Piston diameter 43mm.

thickness of piston rings 1.2mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

Diameter of the piston pin - 11mm.

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Piston benches. The piston group is used for the repair of Chinese, Russian, Belarusian and cheap Eu...

Piston benches. The piston group is used for the repair of Chinese, Russian, Belarusian and cheap European chainsaws of all brands, models 5200.

Diameter of piston 45mm.

thickness of piston rings 1.2mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

Diameter of the piston pin - 11mm.

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing Chinese, Russian, Belarusian and cheap European chainsaws of all brands, mo...

It is used for repairing Chinese, Russian, Belarusian and cheap European chainsaws of all brands, models 5800. Diameter of piston 45.2 mm. The thickness of the piston rings is 1.2mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaws of the Husqvarna brand, models 435, 440, 135, 140. Diameter of pi...

It is used for repairing chainsaws of the Husqvarna brand, models 435, 440, 135, 140. Diameter of piston 41mm. The thickness of the piston ring is 1.5mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 1pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium to improve the removal of heat and increase the resource. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

. Piston group to chainsaw stihl. Applied in MS260 models. Complete piston: cylinder, piston, two p...

. Piston group to chainsaw stihl. Applied in MS260 models.

Complete piston: cylinder, piston, two piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

Diameter of the cylinder internal - 44.7mm.

The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Piston of motorcycle Husqvarna 125, 128, 35mm. Catalog number - 08-62-118 Piston is used in motorcy...

Piston of motorcycle Husqvarna 125, 128, 35mm. Catalog number - 08-62-118

Piston is used in motorcycles Husqvarna 125 models, 128. Diameter of piston 35 mm

In the piston delivery kit you will find: piston, piston ring, piston rings, piston pin

Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile

Piston for brushcutters. Used in for repairing Motorcode Stihl, FS250, FS350 models. Diameter of pis...

Piston for brushcutters. Used in for repairing Motorcode Stihl, FS250, FS350 models. Diameter of piston 40mm.

The piston delivery kit includes:

Piston with oil-containing crop - 1pc.

Ring of piston thickness 1.5 mm - 2 pcs.

pin - 1pc.

pin Rings - 2pcs.

Formal cardboard packaging - 1pc.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Piston is used for repairing chainsaws of Chinese, Russian, Belarusian and inexpensive European bran...

Piston is used for repairing chainsaws of Chinese, Russian, Belarusian and inexpensive European brands, models 4500. Suitable for the dust of this model, all years of release. Diameter of piston 43mm.

The piston delivery kit includes:

Piston with oil-containing crop - 1pc.

Ring of piston thickness 1.2 mm - 2 pcs.

pin - 1pc.

pin Rings - 2pcs.

Formal cardboard packaging - 1pc.

Diameter of the piston pin - 11mm.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Piston is used for repairing chainsaws of Chinese, Russian, Belarusian and inexpensive European bran...

Piston is used for repairing chainsaws of Chinese, Russian, Belarusian and inexpensive European brands, models 5200. Suitable for the dust of this model, all years of release. Piston diameter 45mm.

The piston delivery kit includes:

Piston with oil-containing crop - 1pc.

Ring of piston thickness 1.2 mm - 2 pcs.

pin - 1pc.

pin Rings - 2pcs.

Formal cardboard packaging - 1pc.

Diameter of the piston pin - 11mm.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Piston is used to repair chainsaws of Husqvarna brand, model 137. Suitable for the dust of this mode...

Piston is used to repair chainsaws of Husqvarna brand, model 137. Suitable for the dust of this model, all years of release. Piston diameter 38mm.

The piston delivery kit includes:

Piston with oil-containing crop - 1pc.

Ring piston thickness of 1.5 mm - 1pc.

pin - 1pc.

pin Rings - 2pcs.

Formal cardboard packaging - 1pc.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Piston chainsaws HUSQVARNA 142, 40mm. Catalog number - 08-62-014 In a pack of given piston you will...

Piston chainsaws HUSQVARNA 142, 40mm. Catalog number - 08-62-014

In a pack of given piston you will find: a piston with a diameter of 40 mm, a piston ring with a thickness of 1.5 mm - 1pc, a pin, locking rings of a pin 2 pcs

Piston diameter - 40 mm

Piston height - 34 mm

Piston skirt - 29 mm

The hot belt is 3.5 mm

Height of grooves under the compression ring - 1.5 mm

Diameter for a piston pin - 10 mm

Spare parts manufacturer Trészer - Germany
Hochwertige Bauteile

Piston is used for repairing chainsaws of HUSQVARNA brand, models 345, JONSERED CS2145. Suitable for...

Piston is used for repairing chainsaws of HUSQVARNA brand, models 345, JONSERED CS2145. Suitable for the dust of these models, all years of release.

Also, the piston is used in HUSQVARNA 345R motorcycles.

Piston diameter 42mm.

The piston delivery kit includes:

Piston with oil-containing crop - 1pc.

Ring piston thickness of 1.5 mm - 1pc.

pin - 1pc.

pin Rings - 2pcs.

Formal cardboard packaging - 1pc.

original code HUSQVARNA: # 503 90 73-71

Manufacturer Trészer - Germany.
Hochwertige Bauteile