O.E.M cylinders and pistons

.PORD Group is used for repairing chainsaws JONSERED CS2137, CS2138 partner 350, 351, 352, 370, 371...

.PORD Group is used for repairing chainsaws JONSERED CS2137, CS2138

partner 350, 351, 352, 370, 371, 382, ​​390, 391, 401, 420, 421, 422

poulan - 1950, 2055, 2150, 2250, 2550.

MC CULLOCH 338

Diameter of piston 41mm.

The thickness of the piston ring is 1.5mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston ring - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaws of OLEO-MAC brand, models: 941, EFCO 141. Diameter of piston 40mm...

It is used for repairing chainsaws of OLEO-MAC brand, models: 941, EFCO 141. Diameter of piston 40mm. The thickness of the piston rings is 1.5mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium to improve the removal of heat and increase the resource. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaws of OLEO-MAC brand, models: 947, 952 as well as EFCO 147, 152. Dia...

It is used for repairing chainsaws of OLEO-MAC brand, models: 947, 952 as well as EFCO 147, 152. Diameter of piston 45mm. The thickness of the piston rings is 1.5mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

Chainsaws 947 and 952 have the same landing place for the piston group. This allows you to use one and the same piston set on both models of benzopyl.

The cylinder mirror is covered with chromium to improve the removal of heat and increase the resource. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaws marks Partner, models: 340S, 350S, 360S, ALCO brands, models: BKS...

It is used for repairing chainsaws marks Partner, models: 340S, 350S, 360S, ALCO brands, models: BKS 35/35, BKS 40/40. Diameter of piston 40,5 mm. The thickness of the piston rings is 1.5mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin with a diameter of 10 mm - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium to improve the removal of heat and increase the resource. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

. Cylinder Complete with a . Used in chainsaws STIHL MS361. Cylinder comes in such a complete set: ...

. Cylinder Complete with a . Used in chainsaws STIHL MS361.

Cylinder comes in such a complete set:

Cylinder with Nicasil - 1pcs.

with a diameter of 47 mm. with butter-containing rack - 1pc.

Rings of piston thickness 1.2mm - 2 pcs.

Piston pin - 1pc.

Rings locking pins - 2pcs.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Quality: Premium Substitution.

Recommended: When replacing the piston group, the petroleum petroleum petroleum (knees) connecting a cylinder and a carburetor. Despite the fact that the nozzle is made of benzothyum rubber, over time, it loses its properties, gross and can skip air. The nozzle is inexpensive and makes sense to replace it along with the cylinder.

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaw stihl brands, MS180 models. Diameter of piston 37mm. The thickness...

It is used for repairing chainsaw stihl brands, MS180 models. Diameter of piston 37mm. The thickness of the piston rings is 1.2mm. Diameter of pin 8mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

. The piston group is used for repairing chainsaws STIHL, MOS180 models Piston diameter 38mm. The ...

. The piston group is used for repairing chainsaws STIHL, MOS180 models

Piston diameter 38mm.

The thickness of the piston ring is 1.2mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston ring - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaw stihl brands, MS181, MS211 models. Diameter of piston 40mm. The th...

It is used for repairing chainsaw stihl brands, MS181, MS211 models. Diameter of piston 40mm. The thickness of the piston rings is 1.2mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

diameter of the piston pin 10 mm.

the length of the piston pin 25mm.

Models of chainsaw stihl MS181, MS211 are designed on one platform and have the same landing place for the piston group. This allows you to install one piston group on both models.

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

. Piston group to chainsaw stihl. Applies to STIHL MS210, MS230 models. Complete piston: cylinder, ...

. Piston group to chainsaw stihl. Applies to STIHL MS210, MS230 models.

Complete piston: cylinder, piston, two piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

Diameter of the cylinder inner - 40mm.

The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor.

Pay attention! Due to the listed models have the same landing under the cylinder, we can use this piston on each of them.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

. Piston group to chainsaw stihl. Applied in MS250 models. Complete piston: cylinder, piston, two p...

. Piston group to chainsaw stihl. Applied in MS250 models.

Complete piston: cylinder, piston, two piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

Diameter of the cylinder internal - 42,5 mm.

The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Used in stihl chainsaws, MS360 models. Cylinder comes in the following kit: Cylinder with chromium...

Used in stihl chainsaws, MS360 models.

Cylinder comes in the following kit:

Cylinder with chromium mirrors - 1pc.

Piston with a diameter of 48mm. with butter-containing rack - 1pc.

Rings of piston thickness 1.2mm - 2 pcs.

Piston pin - 1pc.

pin Rings - 2pcs.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaw stihl brands, MS362 models. Diameter of piston 47mm. The thickness...

It is used for repairing chainsaw stihl brands, MS362 models. Diameter of piston 47mm. The thickness of the piston rings is 1.2mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

COLLIVERA COLLA - Nikasil MOS2.

The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Cylinder for stihl. The pore is used in the stihl brands, MS440 models. Cylinder comes in the follo...

Cylinder for stihl. The pore is used in the stihl brands, MS440 models.

Cylinder comes in the following kit:

Cylinder with chromium mirrors. The cylinder is a hole under the decompression valve.- 1 pc.

Piston in diameter 50mm. with butter-containing rack - 1pc.

Rings of piston thickness 1.2mm - 2 pcs.

pin piston diameter 12mm - 1pc.

pin Rings - 2pcs.

Original STIHL code: 1128 020 1227

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

It is used for repairing chainsaws Stihl brands, MS640, MS660 models. Diameter of piston 54 mm. The ...

It is used for repairing chainsaws Stihl brands, MS640, MS660 models. Diameter of piston 54 mm. The thickness of the piston rings is 1.2mm.

The cylinder supplies with a piston to chainsaw includes:

Cylinder - 1pc.

Piston - 1pc.

Piston rings - 2pcs.

pin - 1pc.

Piston Rings - 2pcs

The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.

Piston group to motorcycle. Applies in Chinese motorcycles, Russian and inexpensive European brands....

Piston group to motorcycle. Applies in Chinese motorcycles, Russian and inexpensive European brands. To motorcycle 520 with a piston 44mmIt can also be installed on motorcycles with a piston 40mm thanks to a universal cylinder landing.

Complete piston: cylinder, piston, two piston rings, two locking rings, pin.

The cylinder mirror coating is executed by industrial chromium.

The value of the hardness of the chromium coating is 68 HRC.

The thickness of the working walls of the cylinder is 0.21 mm.

The diameter of the cylinder is internal - 44mm.

The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor.

Manufacturer Trészer - Germany.
Hochwertige Bauteile

Instructions for installing a new cylinder chainsaw and motorcycle

1. Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles.
2. Check and clean the carburetorIt is very important, remove the old fuel tank fuel.
3. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it.
4. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean.
5. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication.
6. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction.
7. Very carefully install the locking rings, do not bend and do not twist them.
8. Lubricate the cylinder and piston rings.
9. Carefully set the cylinder. Use a compression of rings.
10. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used.
11. tighten the screws with the efforts specified by the manufacturer.
12. Gently check the engine. Make sure it rotates freely and without interference.
13. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle.
14. Adjust the carburetor and protest the tool in operation.

Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle.