O.E.M cylinders and pistons produced by TRESZER company


Cylinder and piston kit Trészer Chainsaws ST MS210, MS230, 40mm..

Cylinder and piston kit Trészer Chainsaws ST MS210, MS230, 40mm..

Model name 06-61-023

. Piston group to chainsaw stihl. Applies to STIHL MS210, MS230 models. Complete piston: cylinder, piston, two piston rings, two locking rings, pin. The cylinder mirror coating is executed by industrial chromium. The value of the hardness of the chromium coating is 68 HRC. The thickness of the working walls of the cylinder is 0.21 mm. Diameter of the cylinder inner - 40mm. The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor. Pay attention! Due to the listed models have the same landing under the cylinder, we can use this piston on each of them. Manufacturer Trészer - Germany. Hochwertige Bauteile Instructions for installing a new cylinder chainsaw and motorcycle Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles. Check and clean the carburetorIt is very important, remove the old fuel tank fuel. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction. Very carefully install the locking rings, do not bend and do not twist them. Lubricate the cylinder and piston rings. Carefully set the cylinder. Use a compression of rings. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used. tighten the screws with the efforts specified by the manufacturer. Gently check the engine. Make sure it rotates freely and without interference. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle. Adjust the carburetor and protest the tool in operation. Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle. ..

PRICE 34.66 EUR.

Cylinder and piston kit Trészer Chainsaws ST MS250, 42,5mm..

Cylinder and piston kit Trészer Chainsaws ST MS250, 42,5mm..

Model name 06-61-059

. Piston group to chainsaw stihl. Applied in MS250 models. Complete piston: cylinder, piston, two piston rings, two locking rings, pin. The cylinder mirror coating is executed by industrial chromium. The value of the hardness of the chromium coating is 68 HRC. The thickness of the working walls of the cylinder is 0.21 mm. Diameter of the cylinder internal - 42,5 mm. The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor. Manufacturer Trészer - Germany. Hochwertige Bauteile Instructions for installing a new cylinder chainsaw and motorcycle Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles. Check and clean the carburetorIt is very important, remove the old fuel tank fuel. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction. Very carefully install the locking rings, do not bend and do not twist them. Lubricate the cylinder and piston rings. Carefully set the cylinder. Use a compression of rings. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used. tighten the screws with the efforts specified by the manufacturer. Gently check the engine. Make sure it rotates freely and without interference. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle. Adjust the carburetor and protest the tool in operation. Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle. ..

PRICE 34.66 EUR.

Cylinder and piston kit Trészer Chainsaws ST MS360, 48mm..

Cylinder and piston kit Trészer Chainsaws ST MS360, 48mm..

Model name 06-61-002

Used in stihl chainsaws, MS360 models. s comes in the following kit: Cylinder with chromium mirrors - 1pc. Piston with a diameter of 48mm. with butter-containing rack - 1pc. Rings of piston thickness 1.2mm - 2 pcs. Piston pin - 1pc. pin Rings - 2pcs. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 72.12 EUR.

Cylinder and piston kit Trészer Chainsaws ST MS362, 47mm..

Cylinder and piston kit Trészer Chainsaws ST MS362, 47mm..

Model name 06-61-062

It is used for repairing chainsaw stihl brands, MS362 models. Diameter of piston 47mm. The thickness of the piston rings is 1.2mm. The cylinder supplies with a piston to chainsaw includes: Cylinder - 1pc. Piston - 1pc. Piston rings - 2pcs. pin - 1pc. Piston Rings - 2pcs COLLIVERA COLLA - Nikasil MOS2. The piston group comes in cardboard packaging. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 114.76 EUR.

Cylinder and piston kit Trészer Chainsaws ST MS440, 50mm..

Cylinder and piston kit Trészer Chainsaws ST MS440, 50mm..

Model name 06-61-006

stihl. The pore is used in the stihl brands, MS440 models. s comes in the following kit: Cylinder with chromium mirrors. The cylinder is a hole under the decompression valve.- 1 pc. Piston in diameter 50mm. with butter-containing rack - 1pc. Rings of piston thickness 1.2mm - 2 pcs. pin piston diameter 12mm - 1pc. pin Rings - 2pcs. Original STIHL code: 1128 020 1227 Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 75.75 EUR.

Cylinder and piston kit Trészer Chainsaws ST MS640, MS660, 54mm..

Cylinder and piston kit Trészer Chainsaws ST MS640, MS660, 54mm..

Model name 06-61-007

It is used for repairing chainsaws Stihl brands, MS640, MS660 models. Diameter of piston 54 mm. The thickness of the piston rings is 1.2mm. The cylinder supplies with a piston to chainsaw includes: Cylinder - 1pc. Piston - 1pc. Piston rings - 2pcs. pin - 1pc. Piston Rings - 2pcs The cylinder mirror is covered with chromium. The piston group comes in cardboard packaging. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 95.26 EUR.

Cylinder and piston kit Trészer Motorcosses TL52, 44mm..

Cylinder and piston kit Trészer Motorcosses TL52, 44mm..

Model name 06-61-051

Piston group to motorcycle. Applies in Chinese motorcycles, Russian and inexpensive European brands. To motorcycle 520 with a piston 44mmIt can also be installed on motorcycles with a piston 40mm thanks to a universal cylinder landing. Complete piston: cylinder, piston, two piston rings, two locking rings, pin. The cylinder mirror coating is executed by industrial chromium. The value of the hardness of the chromium coating is 68 HRC. The thickness of the working walls of the cylinder is 0.21 mm. The diameter of the cylinder is internal - 44mm. The coating of the cylinder walls allows you to obtain a resource of work to a full wear of about 900 motor. Manufacturer Trészer - Germany. Hochwertige Bauteile Instructions for installing a new cylinder chainsaw and motorcycle Check that the cylinder which you plan to install is suitable for your model of chainsaw or motorcycles. Check and clean the carburetorIt is very important, remove the old fuel tank fuel. Install a new fuel filter. If you use an old fuel filter, remove all the remnants of the old fuel from it. Clean the carter. Thinking a compressor carter. Carefully check that the carter is clean. Add a bit of lubricants on the bearings. Try to immuse the highest quality lubrication. Wipe a new cylinder duster with a solvent and purge air from compressor The piston and install the piston so that the arrow on it was sent to the exhaust direction. Very carefully install the locking rings, do not bend and do not twist them. Lubricate the cylinder and piston rings. Carefully set the cylinder. Use a compression of rings. Always use a new laying when replacing the cylinder of chainsaw or motorcycle. In some models, the sealant is used. tighten the screws with the efforts specified by the manufacturer. Gently check the engine. Make sure it rotates freely and without interference. For the first refueling, make a fuel mixture in a ratio of 25 - 1 and run a chainsaw or motorcycle. Adjust the carburetor and protest the tool in operation. Note. Failure to comply with these instructions may cause another exit of chainsaw or motorcycle. ..

PRICE 14.90 EUR.

Piston Trészer Chainsaws ST MS361, 47mm..

Piston Trészer Chainsaws ST MS361, 47mm..

Model name 08-62-111

Piston is used for repairing chainsaw stihl brands, MS361 models. Suitable for the dust of this model, all years of release. Diameter of piston 47mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring of piston thickness 1.2 mm - 2 pcs. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 15.39 EUR.

Cylinder and piston kit Trészer Chainsaw Hu 357, 359, 47mm..

Cylinder and piston kit Trészer Chainsaw Hu 357, 359, 47mm..

Model name 06-61-052

It is used for repairing chainsaws of Husqvarna brand, models 357, 359. Diameter of piston 47mm. The thickness of the piston ring is 1.5mm. The cylinder supplies with a piston to chainsaw includes: Cylinder - 1pc. Piston - 1pc. Piston rings - 1pcs. pin - 1pc. Piston Rings - 2pcs The cylinder mirror is covered with chromium to improve the removal of heat and increase the resource. The piston group comes in cardboard packaging. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 74.69 EUR.

Piston Trészer Brushcutters OM SPARTA 25, EF Stark 25, 34mm..

Piston Trészer Brushcutters OM SPARTA 25, EF Stark 25, 34mm..

Model name 08-62-147

Piston of motorcycles. Used to repair Moto-Mac Sparta 25, SPARTA 250T, EFCO STARK 25. Diameter of piston 34mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring piston thickness of 1.5 mm - 1pc. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 10.16 EUR.

Piston Trészer Brushcutters ST FS250, FS350, 40mm..

Piston Trészer Brushcutters ST FS250, FS350, 40mm..

Model name 08-62-132

Piston of motorcycles. Used in for repairing Motorcode Stihl, FS250, FS350 models. Diameter of piston 40mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring of piston thickness 1.5 mm - 2 pcs. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 8.93 EUR.

Piston Trészer Brushcutters ST FS38, FS45, FS55, 34mm..

Piston Trészer Brushcutters ST FS38, FS45, FS55, 34mm..

Model name 262-130

Piston complete with rings of motorcycles. Applies in motorcycle stihl models FS38, FS45, FS55. Includes delivery goes: piston, two piston rings, two locking rings, pin. Piston diameter - 34mm. Thickness of piston rings - 1,5mm. Radial nasech, executed on the walls of the piston, allows you to hold an oil film to improve cooling. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 8.31 EUR.

Piston Trészer Brushcutters ST FS450, 42mm..

Piston Trészer Brushcutters ST FS450, 42mm..

Model name 08-62-134

Piston STIHL FS450, 42mm. Catalog number - 08-62-134 Includes delivery of this piston you will find: piston, two piston rings, pin, two stop piston rings Piston diameter - 42 mm Diameter of the piston pin 10 mm Length of the piston pin 28 mm. ..

PRICE 9.11 EUR.

Piston Trészer Chainsaw 3800, 39mm..

Piston Trészer Chainsaw 3800, 39mm..

Model name 08-62-148

Piston chainsaws 3800, 39mm. Catalog number - 08-62-148 Piston in the kit used for repairing chainsaw Chinese brands model 3800 The piston diameter is 39 mm. Includes delivery you will find: piston, piston rings with a diameter of 39mm, locking rings and pin Spare parts manufacturer Trészer - Germany Hochwertige Bauteile ..

PRICE 6.65 EUR.

Piston Trészer Chainsaw 4500, 43mm..

Piston Trészer Chainsaw 4500, 43mm..

Model name 08-62-102

Piston is used for repairing chainsaws of Chinese, Russian, Belarusian and inexpensive European brands, models 4500. Suitable for the dust of this model, all years of release. Diameter of piston 43mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring of piston thickness 1.2 mm - 2 pcs. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Diameter of the piston pin - 11mm. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 4.59 EUR.

Piston Trészer Chainsaw 5800, D 42.5 mm..

Piston Trészer Chainsaw 5800, D 42.5 mm..

Model name 08-62-127

Piston chainsaw models 5800, 45.2 mm. Catalog number - 08-62-127 Such a piston is used in Chinese chainsocks 5800 Piston diameter 45.2 mm Diameter of the pin - 11mm Includes you will find: piston, two piston rings, two locking rings, pin Spare parts manufacturer Trészer - Germany Hochwertige Bauteile ..

PRICE 4.59 EUR.

Piston Trészer Chainsaw Hu 137, 38mm..

Piston Trészer Chainsaw Hu 137, 38mm..

Model name 08-62-013

Piston is used to repair chainsaws of Husqvarna brand, model 137. Suitable for the dust of this model, all years of release. Piston diameter 38mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring piston thickness of 1.5 mm - 1pc. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 7.02 EUR.

Piston Trészer Chainsaw Hu 236, 240, 39mm..

Piston Trészer Chainsaw Hu 236, 240, 39mm..

Model name 08-62-123

Piston chainsaws HUSQVARNA 236, 240, 39mm. Catalog number - 08-62-123 Applies in chainsaws HUSQVARNA 236, 240, JONSERED CS2234, CS2238 The diameter of this piston is 39mm Includes piston you will find: Piston - 1pc Piston ring - 1pc Piston pin - 1pc Ring the fasten pin - 2pcs Piston can be installed on all of these models of chainsaws all years of release. Spare parts manufacturer Trészer - Germany Hochwertige Bauteile ..

PRICE 7.08 EUR.

Piston Trészer Chainsaw Hu 340, 40mm..

Piston Trészer Chainsaw Hu 340, 40mm..

Model name 08-62-015

Piston chainsaws Husqvarna 340, 40mm. The catalog number is 08-62-015 Piston of this type is used for repairing chainsaws HUSQVARNA 340 models, JONSERED CS2141. Includes piston delivery you will find: piston in diameter 40 mm, piston ring thickness 1.5 mm - 1pc, pin, locking rings 2 pcs Piston diameter - 40 mm Height of grooves under the compression ring - 1.5 mm Diameter for a piston pin - 10 mm Pin lenghts 30mm Spare parts manufacturer Trészer - Germany Hochwertige Bauteile ..

PRICE 8.31 EUR.

Piston Trészer Chainsaw Hu 365, JS C2165, 48mm..

Piston Trészer Chainsaw Hu 365, JS C2165, 48mm..

Model name 08-62-019

Piston is used for repairing chainsaws of the brand HUSQVARNA, models 365, JONSERED CS2165. Suitable for the dust of this model, all years of release. Diameter of piston 48mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring piston thickness of 1.5 mm - 1pc. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 8.93 EUR.

Piston Trészer Chainsaw OM 936, 937, 38mm..

Piston Trészer Chainsaw OM 936, 937, 38mm..

Model name 08-62-105

Piston is used for repairing chainsaw OLEO-MAC 937, 936, EFCO 137. Diameter of piston 38mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring piston thickness of 1.5 mm - 1pc. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Original OLEO-MAC code # 50110066A This piston is suitable for all chainsaw OLEO-MAC models 937 as well as EFCO 137 all years of release. Up to chainsaw OLEO-MAC 936 Use the following manual: If your chainsaw is released before 18.09.2006 and has a factory number to 0356383719 then you need an original piston with code 50050131A. If your chainsaw is released after 18.09.2006 and has a factory number above 0356383720 then use this piston. Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 8.93 EUR.

Piston Trészer Chainsaw OM 940, 941, Mototsey Om Sparta 42, 44, 40mm..

Piston Trészer Chainsaw OM 940, 941, Mototsey Om Sparta 42, 44, 40mm..

Model name 08-62-023

Piston is used for repairing chainsaw OLEO-MAC 941C, 940C, EFCO 140, 141 and OLEO-MAC SPARTA 42, SPARTA 44 and EFCO Stark 42, Stark 44. Suitable for engines of these models, all years of release. Diameter of piston 40mm. The piston delivery kit includes: Piston with oil-containing crop - 1pc. Ring of piston thickness 1.5 mm - 2 pcs. pin - 1pc. pin Rings - 2pcs. Formal cardboard packaging - 1pc. Diameter of pins - 10 mm. Original code EMAK: 50120034A Manufacturer Trészer - Germany. Hochwertige Bauteile ..

PRICE 8.93 EUR.

Piston Trészer Chainsaw PA, JS, 41mm..

Piston Trészer Chainsaw PA, JS, 41mm..

Model name 08-62-056

Piston chainsaw partner, Jonsered, 41mm. The catalog number is 08-62-056 Piston in such a complete set in chainsaws 352 for partners, 371, JONSERED CS2138, POULAN 2150, 2250 Piston diameter 41 mm. Includes piston you will find: piston, piston rings, locking rings, piston pin Spare parts manufacturer Trészer - Germany Hochwertige Bauteile ..

PRICE 7.45 EUR.

Piston Trészer Chainsaw St MS250, 42,5mm..

Piston Trészer Chainsaw St MS250, 42,5mm..

Model name 08-62-003

Piston chainsaws STIHL MS250, 42,5 mm. Catalog number - 08-62-003 In the delivery set of this piston you will find: piston with a diameter of 42.5 mm, piston rings of a thickness of 1.2 mm - 2 pcs, pin, fixing rings of pins 2 pieces Diameter of the piston pin 10 mm Length of the piston pin 28 mm. Spare parts manufacturer Trészer - Germany Hochwertige Bauteile ..

PRICE 7.45 EUR.

Go to next page